Open Die Forging

1. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://www.kt-forge.co.uk/open-die-forging

2. Ball and Roller Bearings

Ball and Roller Bearings; High speed and low friction; Can accommodate radial and small axial loads; Wide variety of sizes available (both Metric and Imperial). Due to its construction, using spheres, the load is focused at the position that the ball contacts the inner race (this is referred to as POINT contact) meaning they can run at high speeds. Ball and Roller Bearings can support both radial (perpendicular to the shaft) and axial loads (parallel to the shaft). For lightly-loaded bearings, balls offer lower friction than rollers. Ball and Roller Bearings can operate when the bearing races are misaligned. A typical application for this bearing would be the internals of a turbocharger where the ability to cope with high speeds and acceleration are at a premium.

http://ball-bearings.online

3. Bearing and Housing Units

Tapered bearings, also known as tapered roller bearings, are a type of rolling element bearing that can support both radial and axial loads. They are designed with tapered inner and outer races and tapered rollers. The shape of the co>

http://ball-bearings.online/categories/bearing-and-housing-units?id_category=13

4. Chesterfield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.bespoke.software.abrt.com

5. Chesterfield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.application.development.grid-itc.com

6. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.application-development.1tsolutions.com

7. High Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

8. Ball and Roller Bearings

A rolling-element bearing, also known as a rolling bearing, is a bearing which carries a load by placing round elements between two bearing rings. The relative motion of the pieces causes the round elements to roll with very little rolling resistance and with little sliding. One of the earliest and best-known rolling-element bearings are sets of logs laid on the ground with a large stone block on top. As the stone is pulled, the logs roll along the ground with little sliding friction. As each log comes out the back, it is moved to the front where the block then rolls on to it. It is possible to imitate such a bearing by placing several pens or pencils on a table and placing an item on top of them. See "bearings" for more on the historical development of bearings. A rolling element rotary bearing uses a shaft in a much larger hole, and cylinders called "rollers" tightly fill the space between the shaft and hole. As the shaft turns, each roller acts as the logs in the above example. However, since the bearing is round, the rollers never fall out from under the load.

http://ball-bearings.online

9.

Vauxhall Motors, commonly known as Vauxhall, is a British automotive manufacturer that has a long and storied history. Vauxhall was founded in 1857 by Alexander Wilson as a pump and marine engine manufacturer in Vauxhall, London, England. In 1903, Vauxhall produced its first automobile, a five-horsepower model, which was followed by the introduction of more advanced vehicles. In 1925, Vauxhall was acquired by General Motors (GM), an American automotive company. This marked the beginning of Vauxhall's affiliation with GM. Under GM's ownership, Vauxhall expanded its production capabilities and introduced a range of successful models, including the Vauxhall 10-4, Vauxhall Victor, and Vauxhall Viva. In 2017, General Motors sold its European division, including Vauxhall, to the PSA Group, a French automotive company that owns brands such as Peugeot and Citroën. Vauxhall continues to operate under the PSA Group and remains a prominent brand in the British automotive market. The company offers a diverse lineup of vehicles, including compact cars like the Vauxhall Corsa, mid-size cars like the Vauxhall Astra, SUVs like the Vauxhall Grandland X, and commercial vehicles like the Vauxhall Vivaro.

http://https://ball-bearings.online/oem/vauxhl/products

10. Salah Timetable

Salah Timetable, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.

http://salah-timetable.jamat-times.com

11. Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

12. Stainless Steel Butt-Weld Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

13. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://application.development.1t-s.com

14. Sheffield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.custom.software.grid-itc.com

15. Cold Forging

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://www.ktforge.co.uk/cold-forging

16. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://1t-s.com/software-development

17. Stainless Steel High Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://high-pressure-fittings.stainless-steel.zx55.com

18. Hot Forming

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://www.ktforge.co.uk/hot-forming

19. Sheffield Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://sheffield.open-source.1t-s.com

20. Doncaster Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.custom.software.1t-s.com

21. Rotherham Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://rotherham.web-design.1t-s.com

22. Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/steel-forging

23. Alternative to Sage Accounts

Ice Ledger accounts system is an ideal alternative for sage accounts, download a fully working copy for free now and get started...

http://iceledger.com/

24. South Yorkshire Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.bespoke.software.abrt.com

25. Cold Forging

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://cold-forging.ktforge.co.uk

26. Computer Maintenance

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://grid-itc.com/computer-maintenance

27. Skip Manager

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.skip-manager.co.uk

28. Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/steel-forging

29. Smith Forging

Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.

http://smith-forging.ktforge.co.uk

30. Rotherham Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.custom-software.1tsolutions.com

31. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://software-development.1tsolutions.com

32. Waste Collection System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.waste-collection-system.skip-manager.co.uk

33. Huddersfield University Accomodation

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/huddersfield-university-accomodation

34. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.software.devlopment.1tsolutions.com

35. Hot Forming

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://hot-forming.kt-forge.co.uk

36. Skip Hire News

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.skip-hire-news.co.uk

37. Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://steel-forging.kt-forge.co.uk

38. Smith Forging

Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.

http://www.kt-forge.co.uk/smith-forging

39. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://grid-itc.com/bespoke-software

40. Jaguar Car Bearings

Jaguar is a British luxury automotive manufacturer known for producing elegant and high-performance cars. Jaguar's roots can be traced back to the Swallow Sidecar Company, founded in 1922 by Sir William Lyons and William Walmsley. Initially, the company produced motorcycle sidecars. In 1935, the company changed its name to SS Cars Ltd. and began producing automobiles. The SS Jaguar 2.5 Litre, introduced in 1935, marked the first use of the Jaguar name on a car. After World War II, the company rebranded as Jaguar Cars Ltd. to avoid associations with the SS initials. In the late 1940s, Jaguar introduced the iconic XK120 sports car, featuring a powerful engine and stunning design. The XK120 established Jaguar's reputation for high-performance vehicles. In 1961, Jaguar launched the E-Type, a groundbreaking sports car that became an instant classic due to its striking design and exceptional performance In 1968, Jaguar merged with the British Motor Corporation (BMC) to form British Motor Holdings, which later became part of the British Leyland conglomerate. In 1989, Jaguar was acquired by Ford Motor Company, which aimed to revitalize the brand. Under Ford's ownership, Jaguar underwent significant modernization and introduced new models such as the Jaguar XK and the luxury sedan Jaguar XJ. The Jaguar S-Type and the Jaguar X-Type were also introduced during this period to expand Jaguar's market reach. In 2008, Ford sold Jaguar and Land Rover to Tata Motors, an Indian automotive company. Under Tata's ownership, Jaguar has continued to evolve and introduce new models, including the Jaguar F-Type sports car, the Jaguar XE compact sedan, and the all-electric Jaguar I-Pace SUV.

http://https://ball-bearings.online/oem/jaguar/products

41. Smith Forging

Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.

http://www.ktforge.co.uk/smith-forging

42. Rod End Bearings

Spherical plain bearings and rod ends. In addition to ball and roller bearings SKF also produces a comprehensive range of spherical plain bearings and rod ends and has a choice of materials for plain and flanged bushings as well as thrust washers. Spherical plain bearings and rod ends are produced in various designs and with various combinations of sliding contact surfaces. Each design and combination has characteristic properties which make it particularly suitable for certain applications. To select a certain bearing type and to establish the requisite bearing size, the main factors which have to be considered are the loads, the load carrying capacity of the bearing and the expected service life. The same is true when selecting a rod end. Selection of bearing type. The choice of the appropriate type of bearing (radial, angular contact or thrust) is determined by the direction of the load which will act on the bearing, while the choice of the appropriate sliding contact surface combination is primarily determined by the way in which the load acts (constant or alternating direction). Radial load: When the load is purely or predominantly radial, a radial spherical plain bearing should be selected. These bearings can accommodate a certain amount of axial load in addition to the radial load. Axial load: When the load is purely or predominantly axial then the choice should be a spherical plain thrust bearing. These bearings can accommodate a certain proportion of radial load in addition to the axial load.

http://ball-bearings.online

43. Rotherham Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.bespoke.software.1t-s.com

44. Doncaster Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.application.development.1t-s.com

45. Student Accomodation Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/student-accomodation-huddersfield

46. Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://web-design.1t-s.com

47. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.software.devlopment.grid-itc.com

48. Angular Contact Bearings

Angular contact ball bearings. Angular contact ball bearings have raceways in the inner and outer rings that are displaced with respect to each other in the direction of the bearing axis. This means that they are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads. The axial load carrying capacity of angular contact ball bearings increases with increasing contact angle. The contact angle a is defined as the angle between the line joining the points of contact of the ball and the raceways in the radial plane, along which the load is transmitted from one raceway to another, and a line perpendicular to the bearing axis. SKF angular contact ball bearings are produced in a wide variety of designs and sizes. Those commonly used and included in this catalogue are: single row angular contact ball bearings; double row angular contact ball bearings; four-point contact ball bearings.

http://ball-bearings.online?pg=rb-acbb

49. Butt-Weld Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.butt-weld-fittings.stainless-steel.zx55.com

50. South Yorkshire Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.bespoke.software.1t-s.com

51. Rotherham Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.custom.software.1t-s.com

52. Huddersfield University Student Accomodation

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/huddersfield-university-student-accomodation

53. Stainless Steel Tubing

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

54. Sheffield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.application.development.grid-itc.com

55. Y-bearings with a tapered bore

Y-bearings in the YSA 2-2FK series have an inner ring extended on both sides and a tapered bore (taper 1:12) enabling them to be mounted on standard adapter sleeves in the H 23 series. The appropriate adapter sleeve is not part of the bearing and must be ordered separately. Y-bearings of this type are delivered exclusively with the rugged standard "Superagriseal" fitted with additional plain sheet steel flingers. The outer ring has two lubrication holes as standard. Mounting onto an adapter sleeve enables the bearings to operate at higher speeds, run more smoothly in applications where the direction of rotation is constant or alternating. The SKF range, which comprises bearings with bore diameter from 25 to 65 mm, fits adapter sleeves in the H 23 series for metric shafts ranging from 20 to 60 mm. These bearings can also be used on adapter sleeves in the HA 23, HE 23 and HS 23 series for inch shafts ranging from 3/4 to 2 3/8 inch diameter.

http://ball-bearings.online?pg=rb-yb-tb

56. Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://1t-s.com/web-design

57. Cooper Split Bearings

A Cooper Split Bearing, also known as a split roller bearing, is a type of bearing that is designed to simplify the installation, inspection, and maintenance process. Unlike traditional bearings that are assembled as a single unit, a Cooper Split Bearing consists of two halves that are split along the horizontal or vertical axis, allowing for easy mounting and dismounting without the need to disassemble surrounding components.

http://ball-bearings.online/categories/cooper-split-bearings?id_category=14

58. Sheffield Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.sheffield.linux.1t-s.com

59. Rooms For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/rooms-for-rent-huddersfield

60. Student Accomodation Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/

61. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://1tsolutions.com/custom-software

62. Bearings for Audi Cars

Audi, the German luxury car manufacturer, uses various types of bearings in their vehicles to ensure smooth and efficient operation. Like other car manufacturers, Audi does not manufacture its own bearings but sources them from reputable bearing manufacturers that meet their quality standards. The specific types of bearings used in Audi cars may vary depending on the model and application. Common types of bearings found in Audi vehicles include Ball Bearings, Roller Bearings, Thrust Bearings and Hub Bearings. When it comes to maintenance or replacement of bearings in an Audi car, it is important to use high-quality bearings from reputable manufacturers that meet Audi's specifications. Following the manufacturer's guidelines and seeking assistance from a professional mechanic or authorized service center is crucial to ensure proper installation and adherence to the vehicle's warranty requirements.

http://ball-bearings.online/oem/audi/products

63. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.software.devlopment.abrt.com

64. Sheffield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.software.devlopment.1tsolutions.com

65. Computer Support

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.1t-s.com/computer-support

66. Stainless Steel Tubing

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

67. Waste Management System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.waste-management-system.skip-manager.com

68. Rotherham Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://rotherham.computer.service.1t-s.com

69. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.custom.software.abrt.com

70. Huddersfield University Student Accomodation

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://huddersfield-university-student-accomodation.iam4rent.co.uk/

71. SKF Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

72. Drop Forging

Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.

http://www.ktforge.co.uk/drop-forging

73. Hygienic Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://hygienic-fittings.stainless-steel.zx55.com

74. Computer Repair

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.1t-s.com/computer-repair

75. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-steel.kt-forge.co.uk

76. Rotherham Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.application.development.abrt.com

77. Drop Forging

Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.

http://drop-forging.ktforge.co.uk

78. Computer Repair

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://1t-s.com/computer-repair

79. Student Accomodation Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/student-accomodation-huddersfield

80. Sheffield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.application.development.1t-s.com

81. Chesterfield Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://chesterfield.open-source.1t-s.com

82. Rotherham Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://www.rotherham.web-design.1t-s.com

83. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.south-yorkshire.custom-software.1tsolutions.com

84. Iveco Truck Bearings

Iveco, an acronym for Industrial Vehicles Corporation, is a multinational manufacturer of commercial vehicles and diesel engines.Iveco was formed in 1974 through the merger of five European companies: Fiat Veicoli Industriali (Italy), OM (Italy), Lancia Veicoli Speciali (Italy), Unic (France), and Magirus-Deutz (Germany). The merger aimed to create a unified entity that could compete on a global scale in the commercial vehicle market. Following the merger, Iveco expanded its product portfolio and manufacturing capabilities, introducing a wide range of commercial vehicles, including trucks, buses, and industrial vehicles. In the 1980s, Iveco acquired several other companies, including Seddon Atkinson (UK) and Pegaso (Spain), further expanding its presence in the European market. During the 1990s and 2000s, Iveco focused on global expansion and diversification, establishing manufacturing facilities and sales networks in various countries outside Europe. In recent years, Iveco has continued to emphasize innovation and sustainability in its product development. The company has introduced advanced technologies, such as telematics systems and connectivity features, to improve vehicle performance, efficiency, and safety. Iveco has also focused on developing eco-friendly solutions, including hybrid and electric vehicles, to address the growing demand for sustainable transportation.

http://ball-bearings.online/oem/iveco/products

85. Bearings Ltd

Looking for Bearings Ltd, look no further. Zx55.com stocks over 40,000 bearings for same day shipping, When it comes to bearing suppliers, zx55.com is the number one online bearings supplier that bearings ltd, bearing king, simply bearings and bearings boys cannot compare.

http://ball-bearings.online

86. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1tsolutions.com/bespoke-software

87. Hygienic Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

88. precision bearings

Machine tools and other precision applications require superior bearing performance. Extended speed capability, a high degree of running accuracy, high system rigidity, low heat generation, and low noise and vibration levels are just some of the performance challenges. To meet the ever-increasing performance requirements of precision applications, SKF and SNFA joined their precision bearing expertise to develop super-precision bearings. The new design super-precision angular contact ball bearings in the 718 (SEA) series are characterized by: high-speed capability, high stiffness, extended fatigue life, easy mounting, compact cross section. SKF-SNFA super-precision angular contact ball bearings in the 718 (SEA) series provide optimum performance in applications where there is a need for high reliability and superior accuracy. The bearings are particularly suitable for machine tool applications, multispindle drilling heads, robotic arms and measuring devices.

http://ball-bearings.online

89. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://abrt.com/software-development

90. Cold Forming

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://cold-forming.kt-forge.co.uk

91. Student Housing Huddersfield

4 Bedroom student housing to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.student-housing-huddersfield.co.uk/

92. Sheffield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.software.devlopment.abrt.com

93. Stainless Steel Pipes

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.pipes.stainless-steel.zx55.com

94. Rooms For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/rooms-for-rent-huddersfield

95. Hot Forging

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://hot-forging.kt-forge.co.uk

96. Barnsley Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.application.development.1t-s.com

97. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1tsolutions.com/software-development

98. Barnsley Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.barnsley.computer.service.1t-s.com

99. Stainless Steel Low Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.low-pressure-fittings.stainless-steel.zx55.com

100. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.south-yorkshire.software.devlopment.abrt.com

101. Hot Forging

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://hot-forging.ktforge.co.uk

102. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://www.ktforge.co.uk/open-die-forging

103. Waste Recycling System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://waste-recycling-system.skip-manager.co.uk

104. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://house-for-rent-huddersfield.iam4share.co.uk/

105. Mazda Car Bearings

Mazda Motor Corporation, a Japanese automotive manufacturer, has a compelling history that spans over 100 years. It was established in 1920 as Toyo Cork Kogyo Co., Ltd., initially manufacturing cork products. In the 1930s, the company diversified into producing machine tools and started developing its first prototype vehicles. After World War II, Toyo Kogyo began producing three-wheeled trucks, evolving into its first passenger car, the Mazda R360, in 1960. Mazda gained international recognition in the 1960s for its development of the Wankel rotary engine, known for its compact size and high power output. The Mazda Cosmo Sport, introduced in 1967, was the first production car powered by a rotary engine and became an iconic symbol of Mazda's engineering prowess. In the 1980s, Mazda expanded its presence worldwide, establishing manufacturing facilities and sales networks in various countries. Mazda formed a strategic partnership with Ford Motor Company in 1979, which led to collaboration in areas such as technology sharing and joint vehicle development. During this period, Mazda introduced notable models like the compact Familia/323, the MX-5 Miata sports car, and the 626 mid-size sedan. In the early 2000s, Mazda adopted a design philosophy called "KODO - Soul of Motion," emphasizing dynamic and expressive styling across its model range. Noteworthy models introduced in recent years include the Mazda3, Mazda6, CX-5, and CX-9, featuring innovative technologies and a balance of performance and efficiency.

http://ball-bearings.online/oem/mazda/products

106. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1t-s.com/application-development

107. Business Contact Manager

Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.

http://www.1t-s.com/contact-manager

108. Barnsley Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.bespoke.software.abrt.com

109. Upset Forging

Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.

http://www.kt-forge.co.uk/upset-forging

110. Volkswagen Car Bearings

Volkswagen, a German automotive manufacturer, has a rich and eventful history that dates back to the 1930s. Volkswagen was founded in 1937 under the German Labour Front, a Nazi trade union, with the goal of producing an affordable "people's car". The company's first model was the iconic Volkswagen Beetle (Type 1), designed by Ferdinand Porsche in 1938. After World War II, Volkswagen's factory in Wolfsburg, Germany, was under British control, but it eventually returned to German ownership. In the 1950s, Volkswagen started exporting Beetles to various countries, including the United States, where it experienced significant success. In the 1970s, Volkswagen expanded its product range beyond the Beetle with the introduction of the Volkswagen Golf (Rabbit in the United States), a compact front-wheel-drive hatchback. Volkswagen acquired other automotive brands, including Audi in 1964, SEAT in 1986, Škoda in 1991, and Bentley, Bugatti, and Lamborghini in the late 1990s. The company also introduced various other successful models, such as the Passat, Jetta, and Polo, catering to different segments of the market. In 2015, Volkswagen faced a major crisis when it was revealed that the company had installed software in its diesel vehicles to cheat on emissions tests, leading to the "dieselgate" scandal. As a result, Volkswagen faced significant financial penalties, legal actions, and a tarnished reputation. In response, Volkswagen has been undergoing a transformation, focusing on electric vehicles (EVs) and sustainable mobility, launching models like the all-electric ID.3 and ID.4.

http://ball-bearings.online/oem/volks/products