Barnsley Application Development

1. Barnsley Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.application-development.1tsolutions.com

2. Sealed Bearings

Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.

http://ball-bearings.online

3. Swaging

T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/swaging

4. Chesterfield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.software.devlopment.grid-itc.com

5. Rotherham Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.custom.software.abrt.com

6. Doncaster Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://doncaster.web-design.1t-s.com

7. Barnsley Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.custom.software.1t-s.com

8. South Yorkshire Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.south-yorkshire.open-source.1t-s.com

9. Weldolets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

10. Cold Forming

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://cold-forming.kt-forge.co.uk

11. Hygienic Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

12. Deep groove ball bearings with filling slots

Single row deep groove ball bearings with filling slots have a filling slot in both the inner and outer ring enabling more and larger balls to be incorporated than in standard deep groove ball bearings. Filling slot bearings have a higher radial load carrying capacity than bearings without filling slots, but their axial load carrying capacity is small. They are also unable to operate at such high speeds as bearings without filling slots. Depending on the main application for which they are used, deep groove ball bearings with filling slots have a cage or no cage.

http://ball-bearings.online?pg=rb-dgbb-fs

13. Stainless Steel Hygienic Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

14. Koyo Bearings

KOYO brand bearings from JTEKT are found virtually anywhere where accurate rotational control is required. Bearing applications vary from jet engine main shaft support, manufacturing equipment used to produce semiconductors and LCD displays, through modern windmills, automobiles, high-speed trains and agricultural machinery to medical equipment, drilling machines at your dentist's surgery and various appliances at your household. We are proud to say: our bearings are found from the heights of the stratosphere to the depths of the ocean - many specially developed to function with optimum efficiency in harsh environments such as weightless or extremely corrosive conditions. In short, you will find Koyo bearings wherever there is a need for innovative engineering and reliability that will last.

http://ball-bearings.online

15. Barnsley Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.bespoke.software.grid-itc.com

16. Deep groove ball bearings

Deep groove ball bearings are used in a particularly wide variety of applications. Consequently, they are available in many executions and sizes. The standard SKF range comprises the following types: single row deep groove ball bearings, SKF Energy Efficient deep groove ball bearings, single row deep groove ball bearings with filling slots, stainless steel single row deep groove ball bearings, double row deep groove ball bearings, single row hybrid deep groove ball bearings, see section Engineering products, single row deep groove ball bearings for high temperatures, Bearings and bearing units for high temperatures

http://ball-bearings.online?pg=dgbb

17. Namaz Times

Namaz Times, Salah Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.

http://namaz-times.jamat-times.com

18. Doncaster Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.doncaster.bespoke.software.grid-itc.com

19. Stainless Steel Flange Gaskets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.flange-gaskets.stainless-steel.zx55.com

20. Spherical Roller Bearings

Spherical roller bearings are inherently self-aligning and very robust. The two rows of rollers make the bearings able to carry heavy loads. Invented by SKF and refined over the years, the present SKF range of spherical roller bearings includes a wide range of sizes of several ISO Dimension Series and also includes special designs, for example, for vibrating screens and similar applications. More recently a range of sealed spherical roller bearings has been added to the assortment. Split spherical roller bearings are usually based on the standard bearings but can be customized as required. Spherical roller bearings have two rows of rollers with a common sphered raceway in the outer ring and two inner ring raceways inclined at an angle to the bearing axis (fig). This gives them an attractive combination of design features making them irreplaceable in many demanding applications. They are self-aligning and consequently insensitive to misalignment of the shaft relative to the housing and to shaft deflection or bending. SKF spherical roller bearings are leading in design and can, in addition to high radial loads, accommodate high axial loads acting in both directions. The standard range of SKF spherical roller bearings comprises: open bearings, sealed bearings, bearings for vibratory applications. In addition to the standard range, SKF offers a wide range of special spherical roller bearings adapted for specific applications.

http://ball-bearings.online

21. Stainless Steel Gaskets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.gaskets.stainless-steel.zx55.com

22. Huddersfield University Student Accomodation

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/huddersfield-university-student-accomodation

23. Computer Support

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://abrt.com/computer-support

24. 304 Stainless Steel

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

25. Barnsley Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.application-development.1tsolutions.com

26. South Yorkshire Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.south-yorkshire.application.development.1t-s.com

27. Alternative to Sage Accounts

Ice Ledger accounts system is an ideal alternative for sage accounts, download a fully working copy for free now and get started...

http://iceledger.com/

28. Sheffield Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.sheffield.linux.1t-s.com

29. Sheffield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.software.devlopment.abrt.com

30. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.south-yorkshire.custom.software.grid-itc.com

31. SKF Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

32. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-steel.kt-forge.co.uk

33. Mazda Car Bearings

Mazda Motor Corporation, a Japanese automotive manufacturer, has a compelling history that spans over 100 years. It was established in 1920 as Toyo Cork Kogyo Co., Ltd., initially manufacturing cork products. In the 1930s, the company diversified into producing machine tools and started developing its first prototype vehicles. After World War II, Toyo Kogyo began producing three-wheeled trucks, evolving into its first passenger car, the Mazda R360, in 1960. Mazda gained international recognition in the 1960s for its development of the Wankel rotary engine, known for its compact size and high power output. The Mazda Cosmo Sport, introduced in 1967, was the first production car powered by a rotary engine and became an iconic symbol of Mazda's engineering prowess. In the 1980s, Mazda expanded its presence worldwide, establishing manufacturing facilities and sales networks in various countries. Mazda formed a strategic partnership with Ford Motor Company in 1979, which led to collaboration in areas such as technology sharing and joint vehicle development. During this period, Mazda introduced notable models like the compact Familia/323, the MX-5 Miata sports car, and the 626 mid-size sedan. In the early 2000s, Mazda adopted a design philosophy called "KODO - Soul of Motion," emphasizing dynamic and expressive styling across its model range. Noteworthy models introduced in recent years include the Mazda3, Mazda6, CX-5, and CX-9, featuring innovative technologies and a balance of performance and efficiency.

http://ball-bearings.online/oem/mazda/products

34. Stainless Steel Butt-Weld Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

35. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.software.devlopment.grid-itc.com

36. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.software.devlopment.abrt.com

37. Chesterfield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.application.development.abrt.com

38. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://open-die-forging.kt-forge.co.uk

39. Roll Forging

Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.

http://roll-forging.kt-forge.co.uk

40. Fiat Car Bearings

Fiat, an Italian automobile manufacturer, has a long and storied history that spans over a century. Fiat, short for Fabbrica Italiana Automobili Torino, was founded on July 11, 1899, in Turin, Italy, by a group of investors led by Giovanni Agnelli. Fiat's first car, the Fiat 4 HP, was produced in 1899. It was a small, lightweight vehicle that helped establish Fiat's reputation for engineering and innovation. In the early 1900s, Fiat expanded its production capacity and introduced various models, including the Fiat 500 "Topolino" and the larger Fiat 508 "Balilla". Fiat experienced significant growth during the 1930s and 1940s, becoming the largest automobile manufacturer in Italy. Models such as the Fiat 1100 and the Fiat 500 "Cinquecento," both of which achieved widespread popularity. Fiat expanded internationally, establishing manufacturing facilities in several countries and acquiring other automotive companies like Lancia and Alfa Romeo. In the 1970s, Fiat continued to expand globally, forming partnerships with foreign manufacturers and establishing joint ventures, producing the Fiat Panda, Fiat Uno, and Fiat Tipo. Fiat also formed a partnership with the American manufacturer Chrysler in 2009, leading to the creation of Fiat Chrysler Automobiles (FCA) in 2014. Recent models include the Fiat 500 and the Fiat Panda gaining popularity. Fiat has also embraced electric mobility, introducing electric versions of its models, including the Fiat 500e.

http://ball-bearings.online/oem/fiat/products

41. Rotherham Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://rotherham.web-design.1t-s.com

42. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.custom.software.1t-s.com

43. Barnsley Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.application.development.1t-s.com

44. Upset Forging

Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.

http://upset-forging.ktforge.co.uk

45. Plain Bearings

Plain bearings. Spherical plain bearings are standardized, ready-to-mount mechanical components that are self-aligning and enable multi-directional alignment movements to be made. The inner ring has a sphered convex outside diameter and the outer ring has a correspondingly sphered but concave inside surface. Rod ends are bearing units that consist of a spherical plain bearing in an eye-shaped head with integral shank - the rod end housing. They are used primarily on the ends of piston rods or together with hydraulic as well as pneumatic cylinders to join the cylinder to associated components. Spherical plain bearings are standardized, ready-to-mount, mechanical components that enable multi-directional, self-aligning movements. The inner ring has a spherical convex outside diameter, while the outer ring has a correspondingly concave inside diameter. The forces acting on the bearing may be static or may occur when the bearing makes oscillating or recurrent tilting and slewing movements at relatively low speeds.

http://ball-bearings.online

46. Stainless Steel Hygienic Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://hygienic-fittings.stainless-steel.zx55.com

47. Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.computer.service.1t-s.com

48. Sheffield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.software.devlopment.1t-s.com

49. Chesterfield Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://chesterfield.open-source.1t-s.com

50. Rotherham Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.application-development.1tsolutions.com

51. Rotherham Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.software.devlopment.1tsolutions.com

52. South Yorkshire Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.bespoke.software.1t-s.com

53. Ball Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

54. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.application-development.1tsolutions.com

55. Stainless Steel Low Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

56. Y-bearings with a standard inner ring

Y-bearings in the 17262(00)-2RS1 and 17263(00)-2RS1 series , with a standard inner ring, have Normal tolerances for the bearing bore diameter and are located on the shaft using an appropriate interference fit. The only difference between these Y-bearings and deep groove ball bearings in the 62 or 63 series is the sphered outside surface of the outer ring. These Y-bearings are suitable for applications where smooth running is a key operating requirement. These bearings can accommodate heavier axial loads than Y-bearings of any other design. The SKF range comprises bearings for metric shafts from 17 to 60 mm.

http://ball-bearings.online?pg=rb-yb-sir

57. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/forging-steel

58. Doncaster Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.doncaster.bespoke-software.1tsolutions.com

59. Barnsley Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.bespoke.software.abrt.com

60. Doncaster Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.application.development.1t-s.com

61. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://open-die-forging.ktforge.co.uk

62. Stainless Steel

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

63. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.custom.software.grid-itc.com

64. Computer Repair

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.grid-itc.com/computer-repair

65. Student Accomodation Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/cheap-student-accomodation-huddersfield

66. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://bespoke.software.grid-itc.com

67. Ball and Roller Bearings

Ball and Roller Bearings; High speed and low friction; Can accommodate radial and small axial loads; Wide variety of sizes available (both Metric and Imperial). Due to its construction, using spheres, the load is focused at the position that the ball contacts the inner race (this is referred to as POINT contact) meaning they can run at high speeds. Ball and Roller Bearings can support both radial (perpendicular to the shaft) and axial loads (parallel to the shaft). For lightly-loaded bearings, balls offer lower friction than rollers. Ball and Roller Bearings can operate when the bearing races are misaligned. A typical application for this bearing would be the internals of a turbocharger where the ability to cope with high speeds and acceleration are at a premium.

http://ball-bearings.online

68. Stainless Steel Flanges

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

69. Barnsley Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.application.development.abrt.com

70. Doncaster Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.software.devlopment.grid-itc.com

71. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.software.devlopment.grid-itc.com

72. South Yorkshire Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://south-yorkshire.linux.1t-s.com

73. Butt-Weld Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

74. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/house-for-rent-huddersfield

75. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.custom.software.grid-itc.com

76. ZX55.com

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

77. Stainless Steel Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.fittings.stainless-steel.zx55.com

78. Inner Rings

An inner ring, also known as an inner race, is a component of a rolling element bearing that is typically mounted on a rotating shaft. It is a ring-shaped part that serves as a raceway for the rolling elements, such as balls or rollers, in the bearing assembly. The inner ring works in conjunction with the outer ring, cage or retainer, and rolling elements to form a complete rolling element bearing. Together, these components enable the bearing to support loads, reduce friction, and facilitate smooth rotation in various applications.

http://ball-bearings.online/categories/inner-rings?id_category=18

79. Engineering Blacksmiths

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/engineering-blacksmiths

80. Thurst Bearings

A thrust bearing is a particular type of rotary bearing. Like other bearings they permit rotation between parts, but they are designed to support a high axial load while doing this. Thrust bearings come in several varieties. Thrust ball bearings, composed of ball bearings supported in a ring, can be used in low thrust applications where there is little axial load. Cylindrical thrust roller bearings consist of small cylindrical rollers arranged flat with their axes pointing to the axis of the bearing. They give very good carrying capacity and are cheap, but tend to wear due to the differences in radial speed and friction which is higher than with ball bearings. Tapered roller thrust bearings consist of small tapered rollers arranged so that their axes all converge at a point on the axis of the bearing. The length of the roller and the diameter of the wide and the narrow ends and the angle of rollers need to be carefully calculated to provide the correct taper so that each end of the roller rolls smoothly on the bearing face without skidding. These are the type most commonly used in automotive applications (to support the wheels of a motor car for example), where they are used in pairs to accommodate axial thrust in either direction, as well as radial loads. They can support rather larger thrust loads than the ball type due to the larger contact area, but are more expensive to manufacture. Spherical roller thrust bearings consists of two rings and asymmetrical rollers of spherical shape. They can accommodate combined radial and axial loads and also accommodate misalignment of the shafts. They are often used together with radial spherical roller bearings. Fluid bearings, where the axial thrust is supported on a thin layer of pressurized liquid, these give low drag. Magnetic bearings, where the axial thrust is supported on a magnetic field. This is used where very high speeds or very low drag is needed, for example the Zippe-type centrifuge. They are commonly used in automotive, marine, and aerospace applications. Thrust bearings are used in cars because the forward gears in modern car gearboxes use helical gears which, while aiding in smoothness and noise reduction, cause axial forces that need to be dealt with. The double helical or herringbone gear balances the thrust caused by normal helical gears. One specific thrust bearing in an automobile is the clutch "throw out" bearing, sometimes called the clutch release bearing.

http://ball-bearings.online

81. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.software.development.1t-s.com

82. Low Pressure BSP Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.low-pressure-bsp-fittings.stainless-steel.zx55.com

83. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://bespoke.software.1t-s.com

84. bicycle wheel bearings

The bicycle wheel bearings sit between a cone screwed to the wheel axle and the cup in the wheel hub. They must be properly adjusted and greased. To find out if they need greasing without taking everything apart, simply remove the wheel from the bike, support the axle horizontally with your fingers, and turn the wheel slowly--try not to tilt the axle as it rotates. If the wheel does not turn smoothly or you can feel tiny bumps in your fingers, then you must dismantle the bearing assembly and service the bearings. Get some good, flat, open wrenches. Make sure they are in sizes 13mm and 15mm. Those are the most common sizes. No other size wrench will work, but any type of adjustable wrench will do for the locking nut. Put the flat wrench on the bearing cone between the hub and the locking nut. Put the adjustable wrench on the locking nut. Hold the bearing cone in place and unscrew the locking nut. The best position to do this is hunched over the wheel while it sits on the ground. Whatever you do,do not open the cones at all while in this position. Just unlock it so you can unscrew everything with your fingers later. Grab the axle on the side that is still locked in place and point the end that you've just loosened, up. Now it is time to unscrew the locking nut almost completely off the axle. Next, unscrew the bearing cone to expose the wheel bearings to the light of day. Any grease in there? Re-grease. The fast way to re-grease your bearings is by just shooting grease in the bearings, screwing the cone back in, flipping the wheel over, hold the cone of the bearing you've just greased, grab the axle now facing up, unscrew it to reveal the other side's bearings and pack them with grease. But the proper way is by taking everything off, clean all the cones, hub cups, bearings, and repack with grease. Reassemble. Screw the bearing cone back into place, but not too tight. Bearings should be able to roll smoothly without axle play. Tighten the lock nut into place and check again.

http://ball-bearings.online

85. Waste Management System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.waste-management-system.skip-manager.com

86. Mercedes Benz Car Bearings

Mercedes-Benz, a German luxury automobile manufacturer, offers a diverse range of car models to cater to various segments and customer preferences. Mercedes-Benz car models include A-Class (entry-level compact car), C-Class (compact executive car), E-Class (mid-size luxury car), S-Class (full-size luxury sedan), GLE-Class (mid-size luxury SUV), GLC-Class (compact luxury SUV), GLA-Class (compact luxury SUV designed for urban environments), GLS-Class (full-size luxury SUV with three rows of seating), G-Class (or "G-Wagon" is a legendary off-road luxury SUV) and AMG Models (high-performance division of Mercedes-Benz). Mercedes-Benz regularly introduces new models and updates existing ones. The availability of specific models may vary by region and time.

http://ball-bearings.online/oem/merc/products

87. 316 Stainless Steel

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://zx55.com

88. Rotherham Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.custom.software.abrt.com

89. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.custom.software.abrt.com

90. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.abrt.com/custom-software

91. Sheffield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.application.development.1t-s.com

92. Volkswagen Car Bearings

Volkswagen, a German automotive manufacturer, has a rich and eventful history that dates back to the 1930s. Volkswagen was founded in 1937 under the German Labour Front, a Nazi trade union, with the goal of producing an affordable "people's car". The company's first model was the iconic Volkswagen Beetle (Type 1), designed by Ferdinand Porsche in 1938. After World War II, Volkswagen's factory in Wolfsburg, Germany, was under British control, but it eventually returned to German ownership. In the 1950s, Volkswagen started exporting Beetles to various countries, including the United States, where it experienced significant success. In the 1970s, Volkswagen expanded its product range beyond the Beetle with the introduction of the Volkswagen Golf (Rabbit in the United States), a compact front-wheel-drive hatchback. Volkswagen acquired other automotive brands, including Audi in 1964, SEAT in 1986, Škoda in 1991, and Bentley, Bugatti, and Lamborghini in the late 1990s. The company also introduced various other successful models, such as the Passat, Jetta, and Polo, catering to different segments of the market. In 2015, Volkswagen faced a major crisis when it was revealed that the company had installed software in its diesel vehicles to cheat on emissions tests, leading to the "dieselgate" scandal. As a result, Volkswagen faced significant financial penalties, legal actions, and a tarnished reputation. In response, Volkswagen has been undergoing a transformation, focusing on electric vehicles (EVs) and sustainable mobility, launching models like the all-electric ID.3 and ID.4.

http://ball-bearings.online/oem/volks/products

93. Sheffield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.bespoke.software.grid-itc.com

94. Computer Maintenance

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://1t-s.com/computer-maintenance

95. Computer Support

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.abrt.com/computer-support

96. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.custom-software.1tsolutions.com

97. Accounts Software for Stockists

Designed for steel stock holders, SASS is a muli-currency accounts system which is ideal for all stockists incorporating Sales, Purchase & Nominal ledgers, Stock Control with emphasis traceability and profits based on actual / real costs ...

http://steelaccounts.com/

98. Rotherham Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://www.rotherham.web-design.1t-s.com

99. Stainless Steel Tubing

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

100. Rotherham Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.application.development.1t-s.com

101. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.software.devlopment.1tsolutions.com

102. Cold Forging

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://www.kt-forge.co.uk/cold-forging

103. Bankrupt Bearings

We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.

http://www.surplus-bearings.co.uk

104. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://house-for-rent-huddersfield.iam4share.co.uk/

105. IP WhoIs

The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.

http://whois.1t-s.com

106. Rotherham Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.bespoke-software.1tsolutions.com

107. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://1t-s.com/custom-software

108. South Yorkshire Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.application-development.1tsolutions.com

109. Stainless Steel Gaskets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

http://www.zx55.com

110. Computer Maintenance

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.abrt.com/computer-maintenance

111. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.abrt.com/bespoke-software

112. Chesterfield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.application.development.1t-s.com