1. Ball Bearings
The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads. It achieves this by using at least two races to contain the balls and transmit the loads through the balls. In most applications, one race is stationary and the other is attached to the rotating assembly (e.g., a hub or shaft). As one of the bearing races rotates it causes the balls to rotate as well. Because the balls are rolling they have a much lower coefficient of friction than if two flat surfaces were sliding against each other. Ball bearings tend to have lower load capacity for their size than other kinds of rolling-element bearings due to the smaller contact area between the balls and races. However, they can tolerate some misalignment of the inner and outer races.
http://ball-bearings.online
2. Stainless Steel Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-bsp-fittings.stainless-steel.zx55.com
3. Cold Forming
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forming.ktforge.co.uk
4. Wheel Bearings Replacement
These instructions apply to bearings in a non-drive wheel. In other words, if your car is front wheel drive, we're talking about the rear bearings. If it's rear wheel drive, you'll be replacing the front wheel bearings. How do I know if I need new wheel bearings? Most of the time we don't even know that they need service. We just drive and never think about them. Most car manufacturers recommend a wheel bearing clean, inspection and repack every 30,000 miles. This is usually done along with the front brake service. They need to be replaced when there is scoring and pitting or they become noisy.
http://ball-bearings.online
5. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.software.devlopment.1tsolutions.com
6. ball-bearings.online
Bearings are mechanical components used to enable smooth and controlled motion between two or more parts. They are designed to reduce friction and support loads, allowing rotating or linear movement with minimal resistance. The primary function of a bearing is to facilitate the relative motion between two parts, typically a rotating shaft and a stationary housing or structure. By providing a low-friction interface between these parts, bearings enable efficient transfer of loads and motion. They are essential components in various machines and mechanical systems, ranging from small devices to large industrial equipment.
http://ball-bearings.online
7. Roller Bearings
A roller bearing is a type of rolling element bearing that is used to reduce friction and support loads in rotating machinery. Unlike ball bearings, which use balls as the rolling elements, roller bearings use cylindrical or tapered rollers. There are different types of roller bearings, including cylindrical roller bearings, tapered roller bearings, spherical roller bearings, and needle roller bearings. Each type has its own specific design and is suitable for different applications and load conditions.
http://ball-bearings.online/categories/roller-bearings?id_category=10
8. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://cold-forging.kt-forge.co.uk
9. Chrysler Car Bearings
Chrysler, as an automotive manufacturer, works with various suppliers for bearings used in their vehicles. Some well-known bearing suppliers include Timken, SKF, NSK and Schaeffler (FAG and INA brands). These are just a few examples of bearing suppliers that Chrysler may work with. It's worth noting that automotive manufacturers often collaborate with multiple suppliers, and the specific suppliers used by Chrysler may vary depending on factors such as region, vehicle model, and production agreements.
http://ball-bearings.online/oem/chrysl/products
10. Waste Collection System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-collection-system.skip-manager.co.uk
11. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.software.devlopment.grid-itc.com
12. Thrust Bearings
A thrust bearing is a particular type of rotary bearing. Like other bearings they permit rotation between parts, but they are designed to support a high axial load while doing this. Thrust bearings come in several varieties. Thrust ball bearings, composed of ball bearings supported in a ring, can be used in low thrust applications where there is little axial load. Cylindrical thrust roller bearings consist of small cylindrical rollers arranged flat with their axes pointing to the axis of the bearing. They give very good carrying capacity and are cheap, but tend to wear due to the differences in radial speed and friction which is higher than with ball bearings. Tapered roller thrust bearings consist of small tapered rollers arranged so that their axes all converge at a point on the axis of the bearing. The length of the roller and the diameter of the wide and the narrow ends and the angle of rollers need to be carefully calculated to provide the correct taper so that each end of the roller rolls smoothly on the bearing face without skidding. These are the type most commonly used in automotive applications (to support the wheels of a motor car for example), where they are used in pairs to accommodate axial thrust in either direction, as well as radial loads. They can support rather larger thrust loads than the ball type due to the larger contact area, but are more expensive to manufacture. Spherical roller thrust bearings consists of two rings and asymmetrical rollers of spherical shape. They can accommodate combined radial and axial loads and also accommodate misalignment of the shafts. They are often used together with radial spherical roller bearings.
http://ball-bearings.online
13. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://roll-forging.ktforge.co.uk
14. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.application-development.1tsolutions.com
15. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://304.stainless-steel.zx55.com
16. Isuzu Vehicle Bearings
Isuzu Motors Ltd. is a Japanese automobile and commercial vehicle manufacturer. Isuzu traces its roots back to Tokyo Ishikawajima Shipbuilding and Engineering Co., Ltd., established in 1916. It initially focused on producing trucks. In 1934, the company introduced its first passenger car, the Isuzu Wolseley Model CA, in collaboration with the British automaker Wolseley Motors. After World War II, the company shifted its focus primarily to commercial vehicles and changed its name to Isuzu Motors Limited in 1949. In 1971, Isuzu formed a strategic alliance with General Motors (GM), resulting in a long-lasting partnership that brought mutual benefits. Isuzu has a strong reputation for producing durable and reliable trucks and commercial vehicles. The company introduced various successful models, including the Isuzu Elf (N-series), Isuzu Forward (F-series), and Isuzu Giga (C/E-series). Isuzu's trucks and commercial vehicles are known for their robustness, fuel efficiency, and versatility, catering to a broad range of industries and applications. Noteworthy models introduced by Isuzu include the Isuzu Trooper (later known as the Isuzu Bighorn and Isuzu Rodeo), Isuzu Amigo, and Isuzu D-Max. Isuzu's SUVs and pickups have gained recognition for their off-road capabilities, durability, and practicality.
http://ball-bearings.online/oem/isuzu/products
17. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://abrt.com/software-development
18. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://www.ktforge.co.uk/cold-forging
19. Tapered Bearings
Tapered bearings, also known as tapered roller bearings, are a type of rolling element bearing that can support both radial and axial loads. They are designed with tapered inner and outer races and tapered rollers. The shape of the components allows for efficient distribution of the load and helps to accommodate axial and radial forces simultaneously. Tapered bearings are commonly used in applications where there are significant axial and radial forces, such as in automotive wheel hubs, heavy machinery, gearboxes, and axle systems. They are known for their durability, reliability, and ability to handle high loads and withstand harsh operating conditions.
http://ball-bearings.online/categories/tapered-bearings?id_category=12
20. Volvo Car Bearings
Volvo Cars is a Swedish automobile manufacturer known for producing premium vehicles with a focus on safety, innovation, and Scandinavian design. Volvo Cars was founded on April 14, 1927, in Gothenburg, Sweden, as a subsidiary of the ball bearing manufacturer SKF. The first Volvo car, the Volvo ÖV4, also known as the "Jakob," rolled off the production line in 1927. In the 1930s, Volvo introduced the PV series, which included popular models like the PV444 and PV544. During World War II, Volvo temporarily shifted its focus to producing military vehicles and equipment. In 1944, Volvo appointed engineer Nils Bohlin, who invented the modern three-point safety belt, making it a standard feature in Volvo cars. In the 1950s and 1960s, Volvo continued to prioritize safety and introduced various safety innovations, including the laminated windshield and the energy-absorbing crumple zone. Volvo expanded internationally, establishing assembly plants in various countries, including Canada and the United States. In 1970, Volvo Cars was acquired by the Ford Motor Company. Under Ford's ownership, Volvo saw further expansion and development. Volvo introduced iconic models such as the Volvo 240, Volvo 740, and Volvo 850, known for their safety features and reliability. In 2010, Ford sold Volvo Cars to Zhejiang Geely Holding Group, a Chinese automotive company. Under Geely's ownership, Volvo Cars underwent a rejuvenation, focusing on modern design, technological innovation, and sustainability. Volvo introduced the SPA (Scalable Product Architecture) platform, which underpins its current vehicle lineup and enables electrification. The company has been committed to electric mobility and launched its first fully electric vehicle, the Volvo XC40 Recharge, in 2020. Volvo Cars aims to become a leader in sustainable mobility, with a plan to be a fully electric car company by 2030.
http://ball-bearings.online/oem/volvo/products
21. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.1t-s.com
22. Sheffield Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://sheffield.linux.1t-s.com
23. Waste Management Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-management-software.skip-manager.co.uk
24. Ball and Roller Bearings
Ball and Roller Bearings; High speed and low friction; Can accommodate radial and small axial loads; Wide variety of sizes available (both Metric and Imperial). Due to its construction, using spheres, the load is focused at the position that the ball contacts the inner race (this is referred to as POINT contact) meaning they can run at high speeds. Ball and Roller Bearings can support both radial (perpendicular to the shaft) and axial loads (parallel to the shaft). For lightly-loaded bearings, balls offer lower friction than rollers. Ball and Roller Bearings can operate when the bearing races are misaligned. A typical application for this bearing would be the internals of a turbocharger where the ability to cope with high speeds and acceleration are at a premium.
http://ball-bearings.online
25. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-diggs-huddersfield.iam4rent.co.uk/
26. Stainless Steel Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
27. Stainless Steel Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
28. Sealed Bearings
Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.
http://ball-bearings.online
29. Mazda Car Bearings
Mazda Motor Corporation, a Japanese automotive manufacturer, has a compelling history that spans over 100 years. It was established in 1920 as Toyo Cork Kogyo Co., Ltd., initially manufacturing cork products. In the 1930s, the company diversified into producing machine tools and started developing its first prototype vehicles. After World War II, Toyo Kogyo began producing three-wheeled trucks, evolving into its first passenger car, the Mazda R360, in 1960. Mazda gained international recognition in the 1960s for its development of the Wankel rotary engine, known for its compact size and high power output. The Mazda Cosmo Sport, introduced in 1967, was the first production car powered by a rotary engine and became an iconic symbol of Mazda's engineering prowess. In the 1980s, Mazda expanded its presence worldwide, establishing manufacturing facilities and sales networks in various countries. Mazda formed a strategic partnership with Ford Motor Company in 1979, which led to collaboration in areas such as technology sharing and joint vehicle development. During this period, Mazda introduced notable models like the compact Familia/323, the MX-5 Miata sports car, and the 626 mid-size sedan. In the early 2000s, Mazda adopted a design philosophy called "KODO - Soul of Motion," emphasizing dynamic and expressive styling across its model range. Noteworthy models introduced in recent years include the Mazda3, Mazda6, CX-5, and CX-9, featuring innovative technologies and a balance of performance and efficiency.
http://ball-bearings.online/oem/mazda/products
30. Stainless Steel High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
31. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/rooms-for-rent-huddersfield
32. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.application.development.1t-s.com
33. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software-development.1tsolutions.com
34. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application-development.1tsolutions.com
35. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://bespoke-software.1tsolutions.com
36. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.custom.software.1t-s.com
37. Stainless Steel Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.low-pressure-bsp-fittings.stainless-steel.zx55.com
38. Chesterfield Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://chesterfield.web-design.1t-s.com
39. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.application-development.1tsolutions.com
40. Forging Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-steel.ktforge.co.uk
41. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
42. Barnsley Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.bespoke.software.abrt.com
43. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://upset-forging.kt-forge.co.uk
44. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.bespoke.software.abrt.com
45. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.bespoke.software.abrt.com
46. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/rooms-for-rent-huddersfield
47. Y-bearings with an eccentric locking collar
Y-bearings with an eccentric locking collar are intended primarily for use in applications where the direction of rotation is constant. On one side of the bearing inner ring is an eccentric extension that fits the locking collar. Turning the locking collar on the inner ring extension in the direction of rotation locks the collar and the bearing onto the shaft. A single grub (set) screw further secures the collar to the shaft. There are two standard series available from SKF: Y-bearings in the YET 2 series have an extended inner ring on one side and are fitted with the rugged "Superagriseal" on both sides. The eccentric collar is zinc-coated. The outer ring has two lubrication holes as standard. Y-bearings in the YEL 2 series have an extended inner ring on both sides . This reduces the extent to which the inner ring can tilt on the shaft, which allows the bearing to run more smoothly. These bearings are fitted with the rugged "Superagriseal", and one of the following flinger options
http://ball-bearings.online?pg=rb-yb-elc
48. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
49. Thurst Bearings
A thrust bearing is a particular type of rotary bearing. Like other bearings they permit rotation between parts, but they are designed to support a high axial load while doing this. Thrust bearings come in several varieties. Thrust ball bearings, composed of ball bearings supported in a ring, can be used in low thrust applications where there is little axial load. Cylindrical thrust roller bearings consist of small cylindrical rollers arranged flat with their axes pointing to the axis of the bearing. They give very good carrying capacity and are cheap, but tend to wear due to the differences in radial speed and friction which is higher than with ball bearings. Tapered roller thrust bearings consist of small tapered rollers arranged so that their axes all converge at a point on the axis of the bearing. The length of the roller and the diameter of the wide and the narrow ends and the angle of rollers need to be carefully calculated to provide the correct taper so that each end of the roller rolls smoothly on the bearing face without skidding. These are the type most commonly used in automotive applications (to support the wheels of a motor car for example), where they are used in pairs to accommodate axial thrust in either direction, as well as radial loads. They can support rather larger thrust loads than the ball type due to the larger contact area, but are more expensive to manufacture. Spherical roller thrust bearings consists of two rings and asymmetrical rollers of spherical shape. They can accommodate combined radial and axial loads and also accommodate misalignment of the shafts. They are often used together with radial spherical roller bearings. Fluid bearings, where the axial thrust is supported on a thin layer of pressurized liquid, these give low drag. Magnetic bearings, where the axial thrust is supported on a magnetic field. This is used where very high speeds or very low drag is needed, for example the Zippe-type centrifuge. They are commonly used in automotive, marine, and aerospace applications. Thrust bearings are used in cars because the forward gears in modern car gearboxes use helical gears which, while aiding in smoothness and noise reduction, cause axial forces that need to be dealt with. The double helical or herringbone gear balances the thrust caused by normal helical gears. One specific thrust bearing in an automobile is the clutch "throw out" bearing, sometimes called the clutch release bearing.
http://ball-bearings.online
50. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/house-for-rent-huddersfield
51. Stainless steel deep groove ball bearings
SKF stainless steel deep groove ball bearings are resistant to corrosion from moisture and several other media. These single row deep groove ball bearings have the same deep raceway grooves and close conformity between raceways and balls as standard deep groove ball bearings made of carbon chromium (rolling bearing) steel. They are without filling slots and can carry axial loads acting in both directions in addition to radial loads, even at high speeds. SKF stainless steel deep groove ball bearings have the same running properties as conventional steel deep groove ball bearings, but have a lower load carrying capacity. The bearings are available in open and sealed designs for shaft diameters from 1 to 50 mm. SKF stainless steel bearings are identified by the designation prefix W, e.g. W 626-2Z.
http://ball-bearings.online?pg=rb-dgbb-ss
52. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application.development.grid-itc.com
53. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://software.development.1t-s.com
54. Rod End Bearings
Spherical plain bearings and rod ends. In addition to ball and roller bearings SKF also produces a comprehensive range of spherical plain bearings and rod ends and has a choice of materials for plain and flanged bushings as well as thrust washers. Spherical plain bearings and rod ends are produced in various designs and with various combinations of sliding contact surfaces. Each design and combination has characteristic properties which make it particularly suitable for certain applications. To select a certain bearing type and to establish the requisite bearing size, the main factors which have to be considered are the loads, the load carrying capacity of the bearing and the expected service life. The same is true when selecting a rod end. Selection of bearing type. The choice of the appropriate type of bearing (radial, angular contact or thrust) is determined by the direction of the load which will act on the bearing, while the choice of the appropriate sliding contact surface combination is primarily determined by the way in which the load acts (constant or alternating direction). Radial load: When the load is purely or predominantly radial, a radial spherical plain bearing should be selected. These bearings can accommodate a certain amount of axial load in addition to the radial load. Axial load: When the load is purely or predominantly axial then the choice should be a spherical plain thrust bearing. These bearings can accommodate a certain proportion of radial load in addition to the axial load.
http://ball-bearings.online
55. Rooms For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://rooms-for-rent-huddersfield.iam4rent.co.uk/
56. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.com
57. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
58. Stainless Steel High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.high-pressure-fittings.stainless-steel.zx55.com
59. Forging Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-steel.kt-forge.co.uk
60. High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.high-pressure-fittings.stainless-steel.zx55.com
61. Waste Collection Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.waste-collection-software.skip-manager.co.uk
62. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.application.development.grid-itc.com
63. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.abrt.com/computer-maintenance
64. Chesterfield Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.chesterfield.open-source.1t-s.com
65. Email Spam Filter
A spam filtering service suitable for small and medium businesses, the 1T Solutions Gatekeeper service is competitively priced, and removes over 95% of e-mail spam and viruses.
http://www.1t-s.com/spam-filter
66. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1t-s.com/bespoke-software
67. Angular Contact Bearings
Angular contact ball bearings. Angular contact ball bearings have raceways in the inner and outer rings that are displaced with respect to each other in the direction of the bearing axis. This means that they are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads. The axial load carrying capacity of angular contact ball bearings increases with increasing contact angle. The contact angle a is defined as the angle between the line joining the points of contact of the ball and the raceways in the radial plane, along which the load is transmitted from one raceway to another, and a line perpendicular to the bearing axis. SKF angular contact ball bearings are produced in a wide variety of designs and sizes. Those commonly used and included in this catalogue are: single row angular contact ball bearings; double row angular contact ball bearings; four-point contact ball bearings.
http://ball-bearings.online?pg=rb-acbb
68. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://abrt.com/computer-maintenance
69. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application.development.abrt.com
70. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.abrt.com
71. Sheffield Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.sheffield.web-design.1t-s.com
72. Swaging
T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.ktforge.co.uk/swaging
73. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://open-die-forging.kt-forge.co.uk
74. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
75. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.custom.software.grid-itc.com
76. Scooter Bearings
If you have plastic core scooter wheels then fitting the bearings is very straight forward as they typically can be pushed in by hand without issue. Fitting scooter bearings into Metal core wheels is a little trickier as they are designed to be a tight fit so pushing them in by hand rarely works. In our workshop we used to use a vise to gently squeeze them in, but now we use a hammer!! Apply a small amount of grease to the edges of each bearing you are going to install. Apply a small amount of grease to the inside hole on the scooter wheel where the bearings are going to be fitted. Place the bearing over the hole in the wheel and try and make sure that it is straight/level as possible. Place either a block of wood or an old paperback book over the top of the bearing and gently strike this with the hammer (Important - do not strike the bearing directly with the hammer). When the bearing has been hammered in fully into the hole in the middle of your wheel it should sit flush with the edge of the wheel Turn the wheel over and insert the bearing spacer (you will need a bearing spacer, if you do not use one your wheel will not spin when you do your axles up securely!)
http://ball-bearings.online
77. South Yorkshire Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://south-yorkshire.linux.1t-s.com
78. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.custom.software.grid-itc.com
79. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://huddersfield-university-student-accomodation.iam4rent.co.uk/
80. High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://high-pressure-fittings.stainless-steel.zx55.com
81. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.custom.software.1t-s.com
82. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/house-for-rent-huddersfield
83. Stainless Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://stainless-steel-forging.kt-forge.co.uk
84. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
85. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
86. Contact Management Software
Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.
http://www.1t-s.com/contact-manager
87. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.software.devlopment.abrt.com
88. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke.software.abrt.com
89. Doncaster Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.custom.software.grid-itc.com
90. South Yorkshire Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.software.devlopment.abrt.com
91. Cold Forging
Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.
http://www.kt-forge.co.uk/cold-forging
92. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.software.devlopment.abrt.com
93. Skip Hire News
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-news.co.uk
94. IP WhoIs
The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.
http://whois.1t-s.com
95. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://house-for-rent-huddersfield.iam4share.co.uk/
96. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://barnsley.custom.software.grid-itc.com
97. Barnsley Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://barnsley.web-design.1t-s.com
98. Bearings By Size
How to measure a bearing. Sometimes you may need to identify a bearing due to general wear and tear. Most bearing references now are laser stamped but these wear and rub off more quickly than the previous method, which was engraved deep in the bearing's metal. Bearing Sizes. Each bearing has an inside diameter, outside diameter and width diameter in that order. Most bearings are metric in size, but can also be imperial. On our site, each bearing shows its principal dimensions. d = Inside diameter, D = Outside diameter, B/T = Width diameter, You can search for a bearing entering this information on the home page in the boxes provided. Once you have identified the bearing's code some bearings come complete with seals or shields. This is known as the suffix in the bearings reference.
http://ball-bearings.online
99. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-stainless-steel.kt-forge.co.uk
100. Stainless Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/stainless-steel-forging
101. Student Accomodation Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-accomodation-huddersfield.iam4share.co.uk/
102. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.custom.software.grid-itc.com
103. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://www.kt-forge.co.uk/upset-forging
104. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-accomodation-huddersfield
105. Opel Car Bearings
Opel is a German automobile manufacturer, founded by Adam Opel in 1862 as a manufacturer of sewing machines in Rüsselsheim, Germany. In 1899, Opel produced its first automobile, the Opel Patent Motor Car, marking its entry into the automotive industry. Opel quickly grew and became one of the largest automobile manufacturers in Germany by the early 20th century. Opel introduced various models, including the Opel 4/8 PS "Doktorwagen," which became a popular model. In 1929, Opel was acquired by General Motors (GM), introduing new models, including the Opel Kadett and Opel Olympia. After World War II, Opel played a significant role in the reconstruction of Germany's automotive industry. Opel introduced popular models like the Opel Rekord, Opel Kapitän, and Opel GT, gaining popularity both domestically and internationally. In the 1970s and 1980s, Opel expanded its lineup with models such as the Opel Manta, Opel Corsa, and Opel Omega. In 2017, General Motors sold Opel and its British sister brand, Vauxhall, to the PSA Group, a French automotive company that owns brands like Peugeot and Citroën. Opel became a part of the newly formed Stellantis N.V., the multinational automotive company resulting from the merger of PSA Group and Fiat Chrysler Automobiles (FCA) in 2021.
http://ball-bearings.online/oem/opel/products
106. Spherical Roller Bearings
Spherical roller bearings are inherently self-aligning and very robust. The two rows of rollers make the bearings able to carry heavy loads. Invented by SKF and refined over the years, the present SKF range of spherical roller bearings includes a wide range of sizes of several ISO Dimension Series and also includes special designs, for example, for vibrating screens and similar applications. More recently a range of sealed spherical roller bearings has been added to the assortment. Split spherical roller bearings are usually based on the standard bearings but can be customized as required. Spherical roller bearings have two rows of rollers with a common sphered raceway in the outer ring and two inner ring raceways inclined at an angle to the bearing axis (fig). This gives them an attractive combination of design features making them irreplaceable in many demanding applications. They are self-aligning and consequently insensitive to misalignment of the shaft relative to the housing and to shaft deflection or bending. SKF spherical roller bearings are leading in design and can, in addition to high radial loads, accommodate high axial loads acting in both directions. The standard range of SKF spherical roller bearings comprises: open bearings, sealed bearings, bearings for vibratory applications. In addition to the standard range, SKF offers a wide range of special spherical roller bearings adapted for specific applications.
http://ball-bearings.online
107. Contact Manager
Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.
http://www.1t-s.com/contact-manager
108. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.tubing.stainless-steel.zx55.com
109. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.co.uk
110. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/software-development
111. Hammer Forging
The most common type of forging equipment is the hammer and anvil. Principles behind the hammer and anvil are still used today in drop-hammer equipment. The principle behind the machine is simple: raise the hammer and drop it or propel it into the workpiece, which rests on the anvil. The main variations between drop-hammers are in the way the hammer is powered; the most common being air and steam hammers. Drop-hammers usually operate in a vertical position. The main reason for this is excess energy (energy that isn't used to deform the workpiece) that isn't released as heat or sound needs to be transmitted to the foundation. Moreover, a large machine base is needed to absorb the impacts. To overcome some shortcomings of the drop-hammer, the counterblow machine or impactor is used. In a counterblow machine both the hammer and anvil move and the workpiece is held between them. Here excess energy becomes recoil. This allows the machine to work horizontally and have a smaller base. Other advantages include less noise, heat and vibration. It also produces a distinctly different flow pattern. Both of these machines can be used for open-die or closed-die forging. A forging press, often just called a press, is used for press forging.
http://hammer-forging.ktforge.co.uk
112. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.abrt.com/software-development
113. Deep groove ball bearings
Deep groove ball bearings are used in a particularly wide variety of applications. Consequently, they are available in many executions and sizes. The standard SKF range comprises the following types: single row deep groove ball bearings, SKF Energy Efficient deep groove ball bearings, single row deep groove ball bearings with filling slots, stainless steel single row deep groove ball bearings, double row deep groove ball bearings, single row hybrid deep groove ball bearings, see section Engineering products, single row deep groove ball bearings for high temperatures, Bearings and bearing units for high temperatures
http://ball-bearings.online?pg=dgbb
114. Shaft Bearings
Shaft Bearings. Propeller and Rudder Shaft Bearings. Water lubricated rubber lined bearings for prop shafts and rudder shafts. Shaft Bearings (also known as Cutlass Bearings) are designed to be water lubricated. They are installed in the stern tube, or bearing housing and support the propeller shaft. The Drive Force range of water lubricated shaft bearings includes: Naval Brass cased shaft bearings, NEW GRP cased shaft bearings (non metallic), Phenolic cased shaft bearings (non metallic) will be replaced by GRP cased bearings, Composite cased shaft bearings (non metallic) will be replaced by GRP cased bearings, Special shaft bearings for Beneteau yachts
http://ball-bearings.online
115. Stainless Steel Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
116. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.bespoke.software.1t-s.com
117. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.grid-itc.com/bespoke-software
118. Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-bsp-fittings.stainless-steel.zx55.com
119. Sockolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.sockolets.zx55.com
120. Needle Roller Bearings
A needle roller bearing is a type of rolling element bearing that uses long, thin cylindrical rollers with a small diameter in proportion to their length. These rollers, known as needle rollers, have a high length-to-diameter ratio, giving them a needle-like appearance and name. Needle roller bearings are designed to support high radial loads with a relatively small cross-sectional area. Needle roller bearings are commonly used in various applications that require compact and lightweight designs with high load-carrying capacity. They are found in automotive transmissions, power tools, motorcycles, industrial machinery, and other equipment where space constraints and high load requirements are present.
http://ball-bearings.online/categories/needle-roller?id_category=17
121. Timeken
Timken Bearing Products. Timken is a leader in all bearing types, including standard anti-friction bearing configurations and advanced products such as housed units, integrated bearing assemblies, precision assemblies and FAA-approved aerospace bearings. Timken Roller Bearings, Tapered Roller Bearings, Spherical Roller Bearings, Cylindrical Roller Bearings, Precision Cylindrical Roller Bearings, Needle Roller Bearings, Thrust Roller Bearings, Timken Ball Bearings, Radial Ball Bearings, Angular Contact Bearings, Precision Bearings, Timken Spherical Plain Bearings, Radial Bearings, Radial Bearings with Lip Seals, Angular Contact Thrust Bearings, Timken High Performance Bearings, AquaSpexx® Trailer Wheel Bearing Kits, AquaSpexx® for Industrial Applications, DuraSpexx® and DuraSpexx® Power Rating Series, Thin Dense Chrome Bearings, Debris Resistant Bearings, Wear-Resistant Bearings, Low Torque Bearings, P900 Bearings, Timken Precision Bearings for Machine Tools, Super Precision Ball Bearings, Precision Tapered Roller Bearings, Ball Screw Support Bearings, Hydra-Rib Variable Preload Bearings, Precision Crossed Roller Bearings, Precision Cylindrical Roller Bearings, Timken Aerospace Bearings, Aerospace Ball Bearings, Aerospace Cylindrical Bearings, Aerospace Tapered Roller Bearings, Aerospace Spherical Roller Bearings, Aircraft Landing Wheel Bearings, Timken Integrated Bearing Assemblies, AP™ Integrated Bearing Assemblies, AP-2™ Integrated Bearing Assemblies, Formed Hub Wheel End System.
http://ball-bearings.online
122. Doncaster Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.custom.software.abrt.com
123. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.application.development.abrt.com
124. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://316.stainless-steel.zx55.com
125. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
126. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.1t-s.com/computer-services
127. Stainless Steel Flange Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.flange-gaskets.stainless-steel.zx55.com
128. Swaging
T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/swaging
129. Sheffield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.custom.software.grid-itc.com
130. Student Accomodation in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://student-accomodation-huddersfield.iam4rent.co.uk/
ball-bearings.online - South Yorkshire Software Development - Huddersfield University Accomodation - Surplus Bearings - Computer Repair - Barnsley Computer Services
Y-bearings with an eccentric locking collar - Rotherham Software Development - Stainless Steel Flange Gaskets - Stainless Steel Hygienic Fittings - Application Development - Student Accomodation in Huddersfield
Bulk Bearings - Timeken - Sheffield Computer Services - Single row deep groove ball bearings - Cold Forming - Waste Recycling Software
Doncaster Custom Software - Computer Repair - Forging Stainless Steel - Engine Bearings - Cooper Split Bearings - Chesterfield Computer Services
Steel Forging - High Pressure Fittings - Barnsley Software Development - South Yorkshire Custom Software - Sheffield Linux - Accounts Software for Stockists
Doncaster Custom Software - Doncaster Application Development - Steel City Bearings - Software Development - Application Development - High Pressure Fittings
Suzuki Vehicle Bearings - Sheffield Custom Software - Rotherham Application Development - Huddersfield University Student Accomodation - Computer Maintenance - Barnsley Software Development
Student Accomodation Huddersfield - 304 Stainless Steel - Sheffield Open Source - Scooter Bearings - Sanitary Fittings - South Yorkshire Software Development
Student Accomodation Huddersfield - Ball and Roller Bearings - SKF Energy Efficient (E2) deep groove ball bearings - Hot Forming - Huddersfield University Student Accomodation - WhoIs
Rotherham Software Development - Computer Support - Custom Software - Forging Stainless Steel - Linux - Custom Software
Barnsley Linux - Bespoke Software - Bike Bearings - Student Accomodation Huddersfield - Forging Steel - House For Rent Huddersfield
Sockolets - Bearing NSK - Computer Support - House to Share Huddersfield - Stainless Steel Butt-Weld Fittings - Roll Forging
Sheffield Application Development - Skip Hire Software - Chesterfield Bespoke Software - Bespoke Software - Software Development - Application Development
House For Rent Huddersfield - Stainless Steel - Wheel Bearings Replacement - Doncaster Custom Software - Rotherham Bespoke Software - Student Diggs in Huddersfield
Doncaster Software Development - Chesterfield Software Development - Shaft Bearings - Ice Ledger, the first full accounting software for start-up companies - Skip Hire News - Huddersfield University Student Accomodation
Salaat Times - Sanitary Fittings - South Yorkshire Custom Software - British Leyland Car Bearings - Stainless Steel Butt-Weld Fittings - Tapered Roller Bearings
Waste Recycling Software - Taper Bearings - House For Rent Huddersfield - Rotherham Linux - Steel Forging - South Yorkshire Software Development
Doncaster Application Development - Skip Hire System - Stainless Steel Valves - Computer Support - Doncaster Bespoke Software - Software Development
Ferrari Car Bearings - Rotherham Custom Software - Sheffield Application Development - South Yorkshire eCommerce - Sheffield eCommerce - Waste Management System
Doncaster Software Development - Barnsley Application Development - South Yorkshire Application Development - Stainless Tube Supplier - Barnsley Linux - Thrust Bearings
Ball Bearings - Student Accomodation in Huddersfield - Forging - Custom Software - Application Development - Sockolets
Huddersfield University Accomodation - Deep groove ball bearings - Pillow Block Bearings - Hygienic Fittings - Detailed WhoIs - Skip Manager
Chesterfield Application Development - Low Pressure BSP Fittings - Stainless Steel Flanges - Student Accomodation in Huddersfield - Barnsley Application Development - Huddersfield University Accomodation
Waste Recycling Software - SKF Bearings Catalogue - Stainless Steel Low Pressure Fittings - SKF Bearings - Software Development - South Yorkshire Open Source
Ford Car Bearings - Custom Software - Student Diggs in Huddersfield - ZX55.com - Student Housing Huddersfield - South Yorkshire Application Development
Spherical Roller Bearings - Stainless Steel Pipes - Doncaster Application Development - Forging Steel - Computer Support - Student Accomodation Huddersfield
Barnsley Custom Software - Software Development - Stainless Steel Fittings - Sheffield Software Development - Rotherham Application Development - Barnsley Application Development
South Yorkshire Application Development - Doncaster Application Development - Anti-Spam - Sheffield Custom Software - Steel Forging - Application Development
Computer Services - Huddersfield University Student Accomodation - Doncaster Bespoke Software - Volvo Car Bearings - Software Development - Hot Forging
Msajid Message Display Board - Rotherham Software Development - Chesterfield Bespoke Software - Stainless Steel Hygienic Fittings - Angular Contact Bearings - Skip Hire Software
Sealed Bearings - 316 Stainless Steel - Application Development - Stainless Steel Fittings - Barnsley Application Development - Stainless Steel High Pressure Fittings
Hot Forming - Open Die Forging - Low Pressure Fittings - Low Pressure BSP Fittings - Skip Hire Software - Stainless Steel Pipes
Application Development - Doncaster Web Design - South Yorkshire Bespoke Software - Renault Car Bearings - Upset Forging - Sheffield Software Development
Computer Services - Forging - Doncaster Application Development - Sheffield Computer Services - Bespoke Software - Bespoke Software
Stainless Steel Low Pressure BSP Fittings - Computer Services - Stainless Steel Forging - Doncaster Computer Services - Rotherham Linux - Steel Forging
Sheffield Software Development - Barnsley Software Development - Barnsley Bespoke Software - Doncaster Custom Software - South Yorkshire Software Development - Business Contact Manager
Barnsley Bespoke Software - Doncaster Computer Services - Chesterfield Custom Software - Skip Hire News - Spam Filter - South Yorkshire Custom Software
Needle Bearings - Stainless Tube Supplier - Motorcycle Bearings - Bearings for Audi Cars - Stainless Steel Tubing - Sheffield Software Development
Stainless Steel Pipes - Chesterfield Custom Software - Inner Rings - Ball Bearings - Chesterfield Computer Services - Butt-Weld Fittings
Stainless Pipe Supplier - Low Pressure Fittings - Cheap Bearings - Student Accomodation Huddersfield - Wheel Bearings - IP WhoIs
Computer Maintenance - Open Die Forging - South Yorkshire Bespoke Software - Stainless Tube Supplier - Student Accomodation Huddersfield - Software Development
Swaging - Bearings for Volvo Trucks - Waste Recycling System - Hub Bearings - Barnsley Custom Software - WhoIs Lookup
Rotherham Bespoke Software - Mercedes Benz Car Bearings - Student Accomodation Huddersfield - Y-bearings with a hexagonal or square bore - Waste Management System - South Yorkshire Application Development
Hot Forming - Computer Systems - Software Development - Computer Repair - Bearings - Stainless Steel Flanges
Software Development - Application Development - Steel Forging - Bespoke Software - Application Development - Sheffield Software Development
Software Development - eCommerce - Threadolets - Open Source - Simply Bearings - Doncaster Application Development
South Yorkshire Custom Software - Waste Recycling System - Huddersfield University Student Accomodation - Barnsley Application Development - Business Accounting Software - Skip Manager
Stainless Steel Low Pressure Fittings - Chesterfield Bespoke Software - House For Rent Huddersfield - Cold Forming - Custom Software - Rotherham Software Development
Stainless Pipe Supplier - Cold Forging - Chesterfield Bespoke Software - Doncaster Bespoke Software - Doncaster Software Development - Application Development
Software Development - Linear Bearings - Rotherham Bespoke Software